CELANEX 5200-2
CELANEX庐 PBT(PBT+PET)-GF15CharacteristicsRegional availabilityProcessingInjection MouldingDelivery formPelletsAdditivesLubricantsSpecial characteristicsHigh GlossProduct TextCelanex 5200-2 is a 15% fiberglass reinforced polyester with improved surface finish. Celanex 5200-2 contains an internal lubricant.Product information
ValueTest NormResin Identification(PBT+PET)-GF15*** 1043Part Marking Code>(PBT+PET)-GF15<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate38cm鲁/10min*** 1133Temperature265掳CLoad2.16kgMelt mass-flow rate28g/10min*** 1133Melt mass-flow rate, Temperature265掳CMelt mass-flow rate, Load2.16kgViscosity number69cm鲁/g*** 307, 1628Moulding shrinkage range, parallel0.4 - 0.6%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus6000MPa*** 527-1/-2Tensile stress at break, 5mm/min120MPa*** 527-1/-2Tensile strain at break, 5mm/min3%*** 527-1/-2Flexural modulus8000MPa*** 178Flexural strength180MPa*** 178Charpy impact strength, 23掳C35kJ/m虏*** 179/1eUCharpy impact strength, -30掳C35kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C8kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C8kJ/m虏*** 179/1eAIzod notched impact strength, 23掳C7.1kJ/m虏*** 180/1AHardness, Rockwell, M-scale91*** 2039-2Poisson&锛�39;s ratio0.35[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min260掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa190掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa215掳C*** 75-1/-2Temperature of deflection under load, 8 MPa65掳C*** 75-1/-2Vicat softening temperature, 50掳C/h 50N210掳C*** 306Coefficient of linear thermal expansion (CLTE), parallel35E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at thickness hHBclassIEC 60695-11-10Thickness tested0.75mmIEC 60695-11-10Oxygen index20%*** 4589-1/-2Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.3IEC 62631-2-1Relative permittivity, 1MHz4IEC 62631-2-1Dissipation factor, 100Hz11E-4IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity>1E13Ohm.mIEC 62631-3-1Surface resistivity>1E15OhmIEC 62631-3-2Electric strength28kV/mmIEC 60243-1Comparative tracking index325IEC 60112Physical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.2%Sim. to *** 62Water absorption, 2mm0.45%Sim. to *** 62Water absorption, Immersion 24h0.05%Sim. to *** 62Density1410kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.02%Melt Temperature Optimum265掳CMin. melt temperature255掳CMax. melt temperature275掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum100掳CMin. mould temperature90掳CMax. mould temperature130掳CAdditional informationProcessing NotesPre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (121掳C) for 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMStandardAdditional InformationStellantis - ChryslerMS.50103 / CPN-2425Black
Copyright 漏 2025 All rights reserved
