| 是否进口：否 | 厂家(产地)：ZG | 牌号： 7716 |
| 销售方式：自产自销 |
CELANEX庐 7716
CELANEX庐 PBT
CELANEX 7716
CELANEX庐 PBTPBT-(GF+MD)35 FR(17)CharacteristicsRegional availabilityNorth America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Product information
ValueTest NormResin IdentificationPBT-(GF+MD)35 FR(17)*** 1043Part Marking Code>PBT-(GF+MD)35 FR(17)<*** 11469Rheological properties
ValueUnitTest NormMelt mass-flow rate6.3g/10min*** 1133Melt mass-flow rate, Temperature250掳CMelt mass-flow rate, Load2.16kgMoulding shrinkage range, parallel0.2 - 0.5%*** 294-4, 2577Moulding shrinkage range, normal0.6 - 0.8%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus10800MPa*** 527-1/-2Tensile stress at break, 5mm/min83MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural modulus11700MPa*** 178Flexural strength140MPa*** 178Charpy impact strength, 23掳C22kJ/m虏*** 179/1eUCharpy impact strength, -30掳C21kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C5kJ/m虏*** 179/1eAIzod notched impact strength, 23掳C4.9kJ/m虏*** 180/1AIzod notched impact strength, -30掳C4.5kJ/m虏*** 180/1AIzod impact strength, 23掳C19kJ/m虏*** 180/1UPoisson&锛�39;s ratio0.34[C]Shore D hardness, 15s83*** 48-4 / *** 868[C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Glass transition temperature, 10掳C/min60掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa194掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa222掳C*** 75-1/-2Coefficient of linear thermal expansion (CLTE), parallel31E-6/K*** 11359-1/-2Coefficient of linear thermal expansion (CLTE), normal46E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at thickness hV-0classIEC 60695-11-10Thickness tested0.8mmIEC 60695-11-10Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.2IEC 62631-2-1Relative permittivity, 1MHz3.9IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity2E14Ohm.mIEC 62631-3-1Surface resistivity5E16OhmIEC 62631-3-2Electric strength24kV/mmIEC 60243-1Comparative tracking index200IEC 60112Arc Resistance124sUL 746BPhysical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.1%Sim. to *** 62Density1690kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.02%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CEjection temperature187掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30掳F (-34掳C) at 250掳F (121掳C) for 4 hours..
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-490(240-255) deg F (deg C)
Nozzle Temperature 480-490(250-255) deg F (deg C)
Melt Temperature 460-490(235-255) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 50% clean and dry regrind may be used for the &锛�39;16 series&锛�39; flame retardant grades.
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (121掳C) for 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationGeneral MotorsBlack; Special Part Approval, Please See Your CE Account Representative.General MotorsNatural; Special Part Approval, Please See Your CE Account Representative.Disclaimer
Privacy Policy
Sitemap
Copyright 漏 2025 All rights reserve
PBT-(GF+MD)35 FR(17)
Characteristics
Regional availability
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Processing
Injection Moulding
Delivery form
Pellets
Special characteristics
Flame retardant, Low Warpage
Product Text
Celanex 7716 is a 35% glass/mineral reinforced, non exuding, flame retarded polybutylene terephthalate which has and excellent balance of mechanical properties and processability. Celanex 7716 is well suited for electrical applications where warp resistance or very flat surfaces are required.
Product information
Value
Test Norm
Resin Identification
PBT-(GF+MD)35 FR(17)
*** 1043
Part Marking Code
>PBT-(GF+MD)35 FR(17)<
*** 11469
Rheological properties
Value
Unit
Test Norm
Melt mass-flow rate
6.3
g/10min
*** 1133
Melt mass-flow rate, Temperature
250
掳C
Melt mass-flow rate, Load
2.16
kg
Moulding shrinkage range, parallel
0.2 - 0.5
%
*** 294-4, 2577
Moulding shrinkage range, normal
0.6 - 0.8
%
*** 294-4, 2577
Mechanical properties
Value
Unit
Test Norm
Tensile modulus
10800
MPa
*** 527-1/-2
Tensile stress at break, 5mm/min
83
MPa
*** 527-1/-2
Tensile strain at break, 5mm/min
1.6
%
*** 527-1/-2
Flexural modulus
11700
MPa
*** 178
Flexural strength
140
MPa
*** 178
Charpy impact strength, 23掳C
22
kJ/m虏
*** 179/1eU
Charpy impact strength, -30掳C
21
kJ/m虏
*** 179/1eU
Charpy notched impact strength, 23掳C
5
kJ/m虏
*** 179/1eA
Charpy notched impact strength, -30掳C
5
kJ/m虏
*** 179/1eA
Izod notched impact strength, 23掳C
4.9
kJ/m虏
*** 180/1A
Izod notched impact strength, -30掳C
4.5
kJ/m虏
*** 180/1A
Izod impact strength, 23掳C
19
kJ/m虏
*** 180/1U
Poisson&锛�39;s ratio
0.34[C]
Shore D hardness, 15s
83
*** 48-4 / *** 868
[C]: Calculated
Thermal properties
Value
Unit
Test Norm
Melting temperature, 10掳C/min
225
掳C
*** 11357-1/-3
Glass transition temperature, 10掳C/min
60
掳C
*** 11357-1/-3
Temperature of deflection under load, 1.8 MPa
194
掳C
*** 75-1/-2
Temperature of deflection under load, 0.45 MPa
222
掳C
*** 75-1/-2
Coefficient of linear thermal expansion (CLTE), parallel
31
E-6/K
*** 11359-1/-2
Coefficient of linear thermal expansion (CLTE), normal
46
E-6/K
*** 11359-1/-2
Flammability
Value
Unit
Test Norm
Burning Behav. at thickness h
V-0
class
IEC 60695-11-10
Thickness tested
0.8
mm
IEC 60695-11-10
Electrical properties
Value
Unit
Test Norm
Relative permittivity, 100Hz
4.2
IEC 62631-2-1
Relative permittivity, 1MHz
3.9
IEC 62631-2-1
Dissipation factor, 1MHz
190
E-4
IEC 62631-2-1
Volume resistivity
2E14
Ohm.m
IEC 62631-3-1
Surface resistivity
5E16
Ohm
IEC 62631-3-2
Electric strength
24
kV/mm
IEC 60243-1
Comparative tracking index
200
IEC 60112
Arc Resistance
124
s
UL 746B
Physical/Other properties
Value
Unit
Test Norm
Humidity absorption, 2mm
0.1
%
Sim. to *** 62
Density
1690
kg/m鲁
*** 1183
Injection
Value
Unit
Drying Recommended
yes
Drying Temperature
120
掳C
Drying Time, Dehumidified Dryer
4
h
Processing Moisture Content
鈮�0.02
%
Melt Temperature Optimum
250
掳C
Min. melt temperature
240
掳C
Max. melt temperature
260
掳C
Screw tangential speed
0.1 - 0.3
m/s
Mold Temperature Optimum
80
掳C
Min. mould temperature
60
掳C
Max. mould temperature
130
掳C
Ejection temperature
187
掳C
Additional information
Injection molding
Preprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30掳F (-34掳C) at 250掳F (121掳C) for 4 hours..
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-490(240-255) deg F (deg C)
Nozzle Temperature 480-490(250-255) deg F (deg C)
Melt Temperature 460-490(235-255) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 50% clean and dry regrind may be used for the &锛�39;16 series&锛�39; flame retardant grades.
Processing Notes
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (121掳C) for 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OCELANEX庐 7716
CELANEX庐 PBT
PBT-(GF+MD)35 FR(17)
Characteristics
Regional availability
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Processing
Injection Moulding
Delivery form
Pellets
Special characteristics
Flame retardant, Low Warpage
Product Text
Celanex 7716 is a 35% glass/mineral reinforced, non exuding, flame retarded polybutylene terephthalate which has and excellent balance of mechanical properties and processability. Celanex 7716 is well suited for electrical applications where warp resistance or very flat surfaces are required.
Product information
Value
Test Norm
Resin Identification
PBT-(GF+MD)35 FR(17)
*** 1043
Part Marking Code
>PBT-(GF+MD)35 FR(17)<
*** 11469
Rheological properties
Value
Unit
Test Norm
Melt mass-flow rate
6.3
g/10min
*** 1133
Melt mass-flow rate, Temperature
250
掳C
Melt mass-flow rate, Load
2.16
kg
Moulding shrinkage range, parallel
0.2 - 0.5
%
*** 294-4, 2577
Moulding shrinkage range, normal
0.6 - 0.8
%
*** 294-4, 2577
Mechanical properties
Value
Unit
Test Norm
Tensile modulus
10800
MPa
*** 527-1/-2
Tensile stress at break, 5mm/min
83
MPa
*** 527-1/-2
Tensile strain at break, 5mm/min
1.6
%
*** 527-1/-2
Flexural modulus
11700
MPa
*** 178
Flexural strength
140
MPa
*** 178
Charpy impact strength, 23掳C
22
kJ/m虏
*** 179/1eU
Charpy impact strength, -30掳C
21
kJ/m虏
*** 179/1eU
Charpy notched impact strength, 23掳C
5
kJ/m虏
*** 179/1eA
Charpy notched impact strength, -30掳C
5
kJ/m虏
*** 179/1eA
Izod notched impact strength, 23掳C
4.9
kJ/m虏
*** 180/1A
Izod notched impact strength, -30掳C
4.5
kJ/m虏
*** 180/1A
Izod impact strength, 23掳C
19
kJ/m虏
*** 180/1U
Poisson&锛�39;s ratio
0.34[C]
Shore D hardness, 15s
83
*** 48-4 / *** 868
[C]: Calculated
Thermal properties
Value
Unit
Test Norm
Melting temperature, 10掳C/min
225
掳C
*** 11357-1/-3
Glass transition temperature, 10掳C/min
60
掳C
*** 11357-1/-3
Temperature of deflection under load, 1.8 MPa
194
掳C
*** 75-1/-2
Temperature of deflection under load, 0.45 MPa
222
掳C
*** 75-1/-2
Coefficient of linear thermal expansion (CLTE), parallel
31
E-6/K
*** 11359-1/-2
Coefficient of linear thermal expansion (CLTE), normal
46
E-6/K
*** 11359-1/-2
Flammability
Value
Unit
Test Norm
Burning Behav. at thickness h
V-0
class
IEC 60695-11-10
Thickness tested
0.8
mm
IEC 60695-11-10
Electrical properties
Value
Unit
Test Norm
Relative permittivity, 100Hz
4.2
IEC 62631-2-1
Relative permittivity, 1MHz
3.9
IEC 62631-2-1
Dissipation factor, 1MHz
190
E-4
IEC 62631-2-1
Volume resistivity
2E14
Ohm.m
IEC 62631-3-1
Surface resistivity
5E16
Ohm
IEC 62631-3-2
Electric strength
24
kV/mm
IEC 60243-1
Comparative tracking index
200
IEC 60112
Arc Resistance
124
s
UL 746B
Physical/Other properties
Value
Unit
Test Norm
Humidity absorption, 2mm
0.1
%
Sim. to *** 62
Density
1690
kg/m鲁
*** 1183
Injection
Value
Unit
Drying Recommended
yes
Drying Temperature
120
掳C
Drying Time, Dehumidified Dryer
4
h
Processing Moisture Content
鈮�0.02
%
Melt Temperature Optimum
250
掳C
Min. melt temperature
240
掳C
Max. melt temperature
260
掳C
Screw tangential speed
0.1 - 0.3
m/s
Mold Temperature Optimum
80
掳C
Min. mould temperature
60
掳C
Max. mould temperature
130
掳C
Ejection temperature
187
掳C
Additional information
Injection molding
Preprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30掳F (-34掳C) at 250掳F (121掳C) for 4 hours..
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-490(240-255) deg F (deg C)
Nozzle Temperature 480-490(250-255) deg F (deg C)
Melt Temperature 460-490(235-255) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 50% clean and dry regrind may be used for the &锛�39;16 series&锛�39; flame retardant grades.
Processing Notes
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (121掳C) for 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEM
Additional Information
General Motors
Black; Special Part Approval, Please See Your CE Account Representative.
General Motors
Natural; Special Part Approval, Please See Your CE Account Representative.
Disclaimer
Privacy Policy
Sitemap
Copyright 漏 2025 All rights reserveEM
Additional Information
General Motors
Black; Special Part Approval, Please See Your CE Account Representative.
General Motors
Natural; Special Part Approval, Please See Your CE Account Representative.
Disclaimer
Privacy Policy
Sitemap
CELANEX庐 7716
CELANEX庐 PBTPBT-(GF+MD)35 FR(17)CharacteristicsRegional availabilityNorth America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Product information
ValueTest NormResin IdentificationPBT-(GF+MD)35 FR(17)*** 1043Part Marking Code>PBT-(GF+MD)35 FR(17)<*** 11469Rheological properties
ValueUnitTest NormMelt mass-flow rate6.3g/10min*** 1133Melt mass-flow rate, Temperature250掳CMelt mass-flow rate, Load2.16kgMoulding shrinkage range, parallel0.2 - 0.5%*** 294-4, 2577Moulding shrinkage range, normal0.6 - 0.8%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus10800MPa*** 527-1/-2Tensile stress at break, 5mm/min83MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural modulus11700MPa*** 178Flexural strength140MPa*** 178Charpy impact strength, 23掳C22kJ/m虏*** 179/1eUCharpy impact strength, -30掳C21kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C5kJ/m虏*** 179/1eAIzod notched impact strength, 23掳C4.9kJ/m虏*** 180/1AIzod notched impact strength, -30掳C4.5kJ/m虏*** 180/1AIzod impact strength, 23掳C19kJ/m虏*** 180/1UPoisson&锛�39;s ratio0.34[C]Shore D hardness, 15s83*** 48-4 / *** 868[C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Glass transition temperature, 10掳C/min60掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa194掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa222掳C*** 75-1/-2Coefficient of linear thermal expansion (CLTE), parallel31E-6/K*** 11359-1/-2Coefficient of linear thermal expansion (CLTE), normal46E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at thickness hV-0classIEC 60695-11-10Thickness tested0.8mmIEC 60695-11-10Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.2IEC 62631-2-1Relative permittivity, 1MHz3.9IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity2E14Ohm.mIEC 62631-3-1Surface resistivity5E16OhmIEC 62631-3-2Electric strength24kV/mmIEC 60243-1Comparative tracking index200IEC 60112Arc Resistance124sUL 746BPhysical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.1%Sim. to *** 62Density1690kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.02%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CEjection temperature187掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30掳F (-34掳C) at 250掳F (121掳C) for 4 hours..
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-490(240-255) deg F (deg C)
Nozzle Temperature 480-490(250-255) deg F (deg C)
Melt Temperature 460-490(235-255) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 50% clean and dry regrind may be used for the &锛�39;16 series&锛�39; flame retardant grades.
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (121掳C) for 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationGeneral MotorsBlack; Special Part Approval, Please See Your CE Account Representative.General MotorsNatural; Special Part Approval, Please See Your CE Account Representative.Disclaimer
Privacy Policy
Sitemap
Copyright 漏 2025 All rights reserveCELANEX庐 7716
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Product information
ValueTest NormResin IdentificationPBT-(GF+MD)35 FR(17)*** 1043Part Marking Code>PBT-(GF+MD)35 FR(17)<*** 11469Rheological properties
ValueUnitTest NormMelt mass-flow rate6.3g/10min*** 1133Melt mass-flow rate, Temperature250掳CMelt mass-flow rate, Load2.16kgMoulding shrinkage range, parallel0.2 - 0.5%*** 294-4, 2577Moulding shrinkage range, normal0.6 - 0.8%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus10800MPa*** 527-1/-2Tensile stress at break, 5mm/min83MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural modulus11700MPa*** 178Flexural strength140MPa*** 178Charpy impact strength, 23掳C22kJ/m虏*** 179/1eUCharpy impact strength, -30掳C21kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C5kJ/m虏*** 179/1eAIzod notched impact strength, 23掳C4.9kJ/m虏*** 180/1AIzod notched impact strength, -30掳C4.5kJ/m虏*** 180/1AIzod impact strength, 23掳C19kJ/m虏*** 180/1UPoisson&锛�39;s ratio0.34[C]Shore D hardness, 15s83*** 48-4 / *** 868[C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Glass transition temperature, 10掳C/min60掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa194掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa222掳C*** 75-1/-2Coefficient of linear thermal expansion (CLTE), parallel31E-6/K*** 11359-1/-2Coefficient of linear thermal expansion (CLTE), normal46E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at thickness hV-0classIEC 60695-11-10Thickness tested0.8mmIEC 60695-11-10Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.2IEC 62631-2-1Relative permittivity, 1MHz3.9IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity2E14Ohm.mIEC 62631-3-1Surface resistivity5E16OhmIEC 62631-3-2Electric strength24kV/mmIEC 60243-1Comparative tracking index200IEC 60112Arc Resistance124sUL 746BPhysical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.1%Sim. to *** 62Density1690kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.02%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CEjection temperature187掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30掳F (-34掳C) at 250掳F (121掳C) for 4 hours..
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-490(240-255) deg F (deg C)
Nozzle Temperature 480-490(250-255) deg F (deg C)
Melt Temperature 460-490(235-255) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 50% clean and dry regrind may be used for the &锛�39;16 series&锛�39; flame retardant grades.
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (121掳C) for 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationGeneral MotorsBlack; Special Part Approval, Please See Your CE Account Representative.General MotorsNatural; Special Part Approval, Please See Your CE Account Representative.Disclaimer
Privacy Policy
Sitemap
Copyright 漏 2025 All rights reserveCELANEX庐 7716
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Product information
ValueTest NormResin IdentificationPBT-(GF+MD)35 FR(17)*** 1043Part Marking Code>PBT-(GF+MD)35 FR(17)<*** 11469Rheological properties
ValueUnitTest NormMelt mass-flow rate6.3g/10min*** 1133Melt mass-flow rate, Temperature250掳CMelt mass-flow rate, Load2.16kgMoulding shrinkage range, parallel0.2 - 0.5%*** 294-4, 2577Moulding shrinkage range, normal0.6 - 0.8%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus10800MPa*** 527-1/-2Tensile stress at break, 5mm/min83MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural modulus11700MPa*** 178Flexural strength140MPa*** 178Charpy impact strength, 23掳C22kJ/m虏*** 179/1eUCharpy impact strength, -30掳C21kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C5kJ/m虏*** 179/1eAIzod notched impact strength, 23掳C4.9kJ/m虏*** 180/1AIzod notched impact strength, -30掳C4.5kJ/m虏*** 180/1AIzod impact strength, 23掳C19kJ/m虏*** 180/1UPoisson&锛�39;s ratio0.34[C]Shore D hardness, 15s83*** 48-4 / *** 868[C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Glass transition temperature, 10掳C/min60掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa194掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa222掳C*** 75-1/-2Coefficient of linear thermal expansion (CLTE), parallel31E-6/K*** 11359-1/-2Coefficient of linear thermal expansion (CLTE), normal46E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at thickness hV-0classIEC 60695-11-10Thickness tested0.8mmIEC 60695-11-10Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.2IEC 62631-2-1Relative permittivity, 1MHz3.9IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity2E14Ohm.mIEC 62631-3-1Surface resistivity5E16OhmIEC 62631-3-2Electric strength24kV/mmIEC 60243-1Comparative tracking index200IEC 60112Arc Resistance124sUL 746BPhysical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.1%Sim. to *** 62Density1690kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.02%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CEjection temperature187掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30掳F (-34掳C) at 250掳F (121掳C) for 4 hours..
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-490(240-255) deg F (deg C)
Nozzle Temperature 480-490(250-255) deg F (deg C)
Melt Temperature 460-490(235-255) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 50% clean and dry regrind may be used for the &锛�39;16 series&锛�39; flame retardant grades.
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (121掳C) for 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationGeneral MotorsBlack; Special Part Approval, Please See Your CE Account Representative.General MotorsNatural; Special Part Approval, Please See Your CE Account Representative.Disclaimer
Privacy Policy
Sitemap
Copyright 漏 2025 All rights reserve
