CELANEX3309HR
CELANEX庐 PBTPBT-GF30CharacteristicsRegional availabilityProcessingInjection MouldingDelivery formPelletsSpecial characteristicsHydrolysis resistantProduct TextCelanex 3309HR is a non-lubricated, 30% fiberglass reinforced Polybutylene Terephthalate which has excellent hydrolysis resistance, mechanical properties and processability.Product information
ValueTest NormResin IdentificationPBT-GF30*** 1043Part Marking Code>PBT-GF30<*** 11469Rheological properties
ValueUnitTest NormMelt mass-flow rate17g/10min*** 1133Melt mass-flow rate, Temperature250掳CMelt mass-flow rate, Load2.16kgMoulding shrinkage range, parallel0.3 - 0.7%*** 294-4, 2577Moulding shrinkage range, normal0.7 - 1.1%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus9200MPa*** 527-1/-2Tensile stress at break, 5mm/min139MPa*** 527-1/-2Tensile strain at break, 5mm/min2.7%*** 527-1/-2Flexural modulus8700MPa*** 178Flexural strength210MPa*** 178Charpy impact strength, 23掳C46kJ/m虏*** 179/1eUCharpy impact strength, -30掳C45kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C8.5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C8.5kJ/m虏*** 179/1eAIzod notched impact strength, 23掳C12kJ/m虏*** 180/1AIzod impact strength, 23掳C35kJ/m虏*** 180/1UPoisson&锛�39;s ratio0.389[OT]Shore D hardness, 15s85*** 48-4 / *** 868[OT]: One time testedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Glass transition temperature, 10掳C/min60掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa205掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa225掳C*** 75-1/-2Vicat softening temperature, 50掳C/h 50N220掳C*** 306Coefficient of linear thermal expansion (CLTE), parallel20[1]E-6/K*** 11359-1/-2Coefficient of linear thermal expansion (CLTE), normal136[1]E-6/K*** 11359-1/-2Coefficient of linear thermal expansion (CLTE), normal, -40-23掳C77E-6/K*** 11359-1/-2Coefficient of linear thermal expansion (CLTE), parallel, -40-23掳C26E-6/K*** 11359-1/-2[1]: 23掳C to 120掳CFlammability
ValueUnitTest NormBurning Behav. at thickness hHBclassIEC 60695-11-10Thickness tested0.71mmIEC 60695-11-10Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.5IEC 62631-2-1Relative permittivity, 1MHz4.1IEC 62631-2-1Dissipation factor, 100Hz22E-4IEC 62631-2-1Dissipation factor, 1MHz160E-4IEC 62631-2-1Volume resistivity>1E13Ohm.mIEC 62631-3-1Surface resistivity>1E15OhmIEC 62631-3-2Electric strength31kV/mmIEC 60243-1Comparative tracking index425IEC 60112Physical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.16%Sim. to *** 62Density1530kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.02%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CEjection temperature184掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30掳F (-34掳C) at 250掳F (121掳C) for 4 hours.
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-500(240-260) deg F (deg C)
Nozzle Temperature 480-500(250-260) deg F (deg C)
Melt Temperature 460-500(235-260) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Processing NotesPre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (121掳C) for 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMStandardAdditional InformationContinentalTST N 055 47.27(TST N 055 47.27-000)FordWSS-M4D929-A3NaturalFordWSS-M4D929-A3BlackHyundaiMS941-03 Type F-5Li AutoQ/LiA53100382021 (V2)NissanPBTP(G30)-1NX-1RenaultNo Spec, Special Part Approval, See Your CE Account Manager.VW GroupVW 50136
Copyright 漏 2025 All rights reserved.
