| 是否进口：否 | 厂家(产地)：ZG | 牌号： 2302 GV1/30 ECO-R |
| 销售方式：自产自销 |
CELANEX 2302 GV1/30 ECO-R Product information Rheological properties Mechanical properties Thermal properties Flammability Electrical properties Physical/Other properties Injection Preprocessing Pre-Drying
Celanex庐 2302 GV1/30 ECO-R incorporates 25% of post-consumer recycled Polyethylene terephthalate (PCR-PET) by weight in the finished product.
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 2 to 4 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 265-275 掳C
Mold Temperature *) 90-100 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
CELANEX should in principle be predried. Because of the necessary low maximum residual moisture content the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Disclaimer
Privacy Policy
Sitemap
Copyright 漏 2025 All rights reserved.
CELANEX庐 2302 GV1/30 ECO-R
CELANEX庐 PBT(PBT+PET)-GF30CharacteristicsProcessingInjection MouldingDelivery formPelletsAdditivesRelease agentSpecial characteristicsHeat stabilised or stable to heat, High GlossSustainabilityRecycled ContentProduct TextChemical abbreviation according *** 1043-1: PBT+PET Moulding compound *** 7792- PBT/PET, MGHR, 08-110N, GF30. Polybutylene terephthalate (PBT) / recycled Polyethylene terephthalate (R-PET) polymer blend, 30% glass fiber reinforced, for injection molded parts with superior gloss.Product information
ValueTest NormResin Identification(PBT+PET)-GF30*** 1043Part Marking Code>(PBT+PET)-GF30<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate14cm鲁/10min*** 1133Temperature265掳CLoad2.16kgMechanical properties
ValueUnitTest NormTensile modulus10000MPa*** 527-1/-2Tensile stress at break, 5mm/min145MPa*** 527-1/-2Tensile strain at break, 5mm/min2.2%*** 527-1/-2Flexural modulus8600MPa*** 178Flexural strength220MPa*** 178Charpy notched impact strength, 23掳C8.5kJ/m虏*** 179/1eAPoisson&锛�39;s ratio0.34[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min250掳C*** 11357-1/-3Flammability
ValueUnitTest NormOxygen index20%*** 4589-1/-2Glow Wire Flammability Index, 1.0mm675掳CIEC 60695-2-12Glow Wire Ignition Temperature, 1.0mm700掳CIEC 60695-2-13FMVSS ClassB*** 3795 (FMVSS 302)Burning rate, Thickness 1 mm69mm/min*** 3795 (FMVSS 302)Electrical properties
ValueTest NormComparative tracking index250IEC 60112Physical/Other properties
ValueUnitTest NormDensity1550kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4 - 6hProcessing Moisture Content鈮�0.02%Melt Temperature Optimum265掳CMin. melt temperature255掳CMax. melt temperature275掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum100掳CMin. mould temperature90掳CMax. mould temperature130掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 2 to 4 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 265-275 掳C
Mold Temperature *) 90-100 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
Pre-Drying
CELANEX should in principle be predried. Because of the necessary low maximum residual moisture content the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Disclaimer
Privacy Policy
Sitemap
Copyright 漏 2025 All rights reserved.CELANEX庐 2302 GV1/30 ECO-R
Product information
ValueTest NormResin Identification(PBT+PET)-GF30*** 1043Part Marking Code>(PBT+PET)-GF30<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate14cm鲁/10min*** 1133Temperature265掳CLoad2.16kgMechanical properties
ValueUnitTest NormTensile modulus10000MPa*** 527-1/-2Tensile stress at break, 5mm/min145MPa*** 527-1/-2Tensile strain at break, 5mm/min2.2%*** 527-1/-2Flexural modulus8600MPa*** 178Flexural strength220MPa*** 178Charpy notched impact strength, 23掳C8.5kJ/m虏*** 179/1eAPoisson&锛�39;s ratio0.34[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min250掳C*** 11357-1/-3Flammability
ValueUnitTest NormOxygen index20%*** 4589-1/-2Glow Wire Flammability Index, 1.0mm675掳CIEC 60695-2-12Glow Wire Ignition Temperature, 1.0mm700掳CIEC 60695-2-13FMVSS ClassB*** 3795 (FMVSS 302)Burning rate, Thickness 1 mm69mm/min*** 3795 (FMVSS 302)Electrical properties
ValueTest NormComparative tracking index250IEC 60112Physical/Other properties
ValueUnitTest NormDensity1550kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4 - 6hProcessing Moisture Content鈮�0.02%Melt Temperature Optimum265掳CMin. melt temperature255掳CMax. melt temperature275掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum100掳CMin. mould temperature90掳CMax. mould temperature130掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 2 to 4 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 265-275 掳C
Mold Temperature *) 90-100 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
Pre-Drying
CELANEX should in principle be predried. Because of the necessary low maximum residual moisture content the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
