| 是否进口：否 | 厂家(产地)：ZG | 牌号：2300 GV1/50 |
| 销售方式：自产自销 |
CELANEX庐 2300 GV1/50
CELANEX庐 PBTPBT-GF50CharacteristicsRegional availabilityProcessingInjection MouldingDelivery formPelletsAdditivesRelease agentSpecial characteristicsHeat stabilised or stable to heatProduct TextChemical abbreviation according to *** 1043: PBT GF50. Moulding compound *** 7792-1 PBT, MGAR, 08-160, GF50. Polybutylene terephthalate, 50 % glass fiber reinforced. Flammability UL 94 HB minimum thickness 0.82 mm. Recognition by Underwriters Laboratories, USA (UL)Product information
ValueTest NormResin IdentificationPBT-GF50*** 1043Part Marking Code>PBT-GF50<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate5cm鲁/10min*** 1133Temperature250掳CLoad2.16kgMoulding shrinkage range, parallel0.3 - 0.4%*** 294-4, 2577Moulding shrinkage range, normal0.7 - 0.9%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus17000MPa*** 527-1/-2Tensile stress at break, 5mm/min165MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural strength240MPa*** 178Tensile creep modulus, 1h12500MPa*** 899-1Tensile creep modulus, 1000h9500MPa*** 899-1Charpy impact strength, 23掳C70kJ/m虏*** 179/1eUCharpy impact strength, -30掳C65kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C11.5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C11.5kJ/m虏*** 179/1eABall indentation hardness, H 961/30235MPa*** 2039-1Poisson&锛�39;s ratio0.33[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa215掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa228掳C*** 75-1/-2Temperature of deflection under load, 8 MPa185掳C*** 75-1/-2Vicat softening temperature, 50掳C/h 50N225掳C*** 306Coefficient of linear thermal expansion (CLTE), parallel15E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at 1.5mm nom. thickn.HBclassIEC 60695-11-10Thickness tested1.6mmIEC 60695-11-10Burning Behav. at thickness hHBclassIEC 60695-11-10Thickness tested0.82mmIEC 60695-11-10UL recognitionyesUL 94Oxygen index20%*** 4589-1/-2Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.4IEC 62631-2-1Relative permittivity, 1MHz4.1IEC 62631-2-1Dissipation factor, 100Hz16E-4IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity>1E13Ohm.mIEC 62631-3-1Surface resistivity>1E15OhmIEC 62631-3-2Electric strength35kV/mmIEC 60243-1Physical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.15%Sim. to *** 62Water absorption, 2mm0.35%Sim. to *** 62Density1710kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.04%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 4 to 6 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 260-270 掳C
Mold Temperature *) 75-85 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided. For grades containing flame retardants, a maximum temperature of 265 掳C should not be exceeded.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
Pre-Drying
CELANEX should always be dried before processing. Because of the necessary low maximum residual moisture content, the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationVW GroupNATURAL, no spec, special part approvalDiagrams
Copyright 漏 2025 All rights reserved.
CELANEX庐 2300 GV1/50
CELANEX庐 PBTPBT-GF50CharacteristicsRegional availabilityProcessingInjection MouldingDelivery formPelletsAdditivesRelease agentSpecial characteristicsHeat stabilised or stable to heatProduct TextChemical abbreviation according to *** 1043: PBT GF50. Moulding compound *** 7792-1 PBT, MGAR, 08-160, GF50. Polybutylene terephthalate, 50 % glass fiber reinforced. Flammability UL 94 HB minimum thickness 0.82 mm. Recognition by Underwriters Laboratories, USA (UL)Product information
ValueTest NormResin IdentificationPBT-GF50*** 1043Part Marking Code>PBT-GF50<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate5cm鲁/10min*** 1133Temperature250掳CLoad2.16kgMoulding shrinkage range, parallel0.3 - 0.4%*** 294-4, 2577Moulding shrinkage range, normal0.7 - 0.9%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus17000MPa*** 527-1/-2Tensile stress at break, 5mm/min165MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural strength240MPa*** 178Tensile creep modulus, 1h12500MPa*** 899-1Tensile creep modulus, 1000h9500MPa*** 899-1Charpy impact strength, 23掳C70kJ/m虏*** 179/1eUCharpy impact strength, -30掳C65kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C11.5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C11.5kJ/m虏*** 179/1eABall indentation hardness, H 961/30235MPa*** 2039-1Poisson&锛�39;s ratio0.33[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa215掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa228掳C*** 75-1/-2Temperature of deflection under load, 8 MPa185掳C*** 75-1/-2Vicat softening temperature, 50掳C/h 50N225掳C*** 306Coefficient of linear thermal expansion (CLTE), parallel15E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at 1.5mm nom. thickn.HBclassIEC 60695-11-10Thickness tested1.6mmIEC 60695-11-10Burning Behav. at thickness hHBclassIEC 60695-11-10Thickness tested0.82mmIEC 60695-11-10UL recognitionyesUL 94Oxygen index20%*** 4589-1/-2Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.4IEC 62631-2-1Relative permittivity, 1MHz4.1IEC 62631-2-1Dissipation factor, 100Hz16E-4IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity>1E13Ohm.mIEC 62631-3-1Surface resistivity>1E15OhmIEC 62631-3-2Electric strength35kV/mmIEC 60243-1Physical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.15%Sim. to *** 62Water absorption, 2mm0.35%Sim. to *** 62Density1710kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.04%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 4 to 6 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 260-270 掳C
Mold Temperature *) 75-85 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided. For grades containing flame retardants, a maximum temperature of 265 掳C should not be exceeded.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
Pre-Drying
CELANEX should always be dried before processing. Because of the necessary low maximum residual moisture content, the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationVW GroupNATURAL, no spec, special part approvalDiagrams
Copyright 漏 2025 All rights reserved.
CELANEX庐 2300 GV1/50
CELANEX庐 PBTPBT-GF50CharacteristicsRegional availabilityProcessingInjection MouldingDelivery formPelletsAdditivesRelease agentSpecial characteristicsHeat stabilised or stable to heatProduct TextChemical abbreviation according to *** 1043: PBT GF50. Moulding compound *** 7792-1 PBT, MGAR, 08-160, GF50. Polybutylene terephthalate, 50 % glass fiber reinforced. Flammability UL 94 HB minimum thickness 0.82 mm. Recognition by Underwriters Laboratories, USA (UL)Product information
ValueTest NormResin IdentificationPBT-GF50*** 1043Part Marking Code>PBT-GF50<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate5cm鲁/10min*** 1133Temperature250掳CLoad2.16kgMoulding shrinkage range, parallel0.3 - 0.4%*** 294-4, 2577Moulding shrinkage range, normal0.7 - 0.9%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus17000MPa*** 527-1/-2Tensile stress at break, 5mm/min165MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural strength240MPa*** 178Tensile creep modulus, 1h12500MPa*** 899-1Tensile creep modulus, 1000h9500MPa*** 899-1Charpy impact strength, 23掳C70kJ/m虏*** 179/1eUCharpy impact strength, -30掳C65kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C11.5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C11.5kJ/m虏*** 179/1eABall indentation hardness, H 961/30235MPa*** 2039-1Poisson&锛�39;s ratio0.33[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa215掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa228掳C*** 75-1/-2Temperature of deflection under load, 8 MPa185掳C*** 75-1/-2Vicat softening temperature, 50掳C/h 50N225掳C*** 306Coefficient of linear thermal expansion (CLTE), parallel15E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at 1.5mm nom. thickn.HBclassIEC 60695-11-10Thickness tested1.6mmIEC 60695-11-10Burning Behav. at thickness hHBclassIEC 60695-11-10Thickness tested0.82mmIEC 60695-11-10UL recognitionyesUL 94Oxygen index20%*** 4589-1/-2Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.4IEC 62631-2-1Relative permittivity, 1MHz4.1IEC 62631-2-1Dissipation factor, 100Hz16E-4IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity>1E13Ohm.mIEC 62631-3-1Surface resistivity>1E15OhmIEC 62631-3-2Electric strength35kV/mmIEC 60243-1Physical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.15%Sim. to *** 62Water absorption, 2mm0.35%Sim. to *** 62Density1710kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.04%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 4 to 6 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 260-270 掳C
Mold Temperature *) 75-85 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided. For grades containing flame retardants, a maximum temperature of 265 掳C should not be exceeded.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
Pre-Drying
CELANEX should always be dried before processing. Because of the necessary low maximum residual moisture content, the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationVW GroupNATURAL, no spec, special part approvalDiagrams
Copyright 漏 2025 All rights reserved.
CELANEX庐 2300 GV1/50
CELANEX庐 PBTPBT-GF50CharacteristicsRegional availabilityProcessingInjection MouldingDelivery formPelletsAdditivesRelease agentSpecial characteristicsHeat stabilised or stable to heatProduct TextChemical abbreviation according to *** 1043: PBT GF50. Moulding compound *** 7792-1 PBT, MGAR, 08-160, GF50. Polybutylene terephthalate, 50 % glass fiber reinforced. Flammability UL 94 HB minimum thickness 0.82 mm. Recognition by Underwriters Laboratories, USA (UL)Product information
ValueTest NormResin IdentificationPBT-GF50*** 1043Part Marking Code>PBT-GF50<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate5cm鲁/10min*** 1133Temperature250掳CLoad2.16kgMoulding shrinkage range, parallel0.3 - 0.4%*** 294-4, 2577Moulding shrinkage range, normal0.7 - 0.9%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus17000MPa*** 527-1/-2Tensile stress at break, 5mm/min165MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural strength240MPa*** 178Tensile creep modulus, 1h12500MPa*** 899-1Tensile creep modulus, 1000h9500MPa*** 899-1Charpy impact strength, 23掳C70kJ/m虏*** 179/1eUCharpy impact strength, -30掳C65kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C11.5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C11.5kJ/m虏*** 179/1eABall indentation hardness, H 961/30235MPa*** 2039-1Poisson&锛�39;s ratio0.33[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa215掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa228掳C*** 75-1/-2Temperature of deflection under load, 8 MPa185掳C*** 75-1/-2Vicat softening temperature, 50掳C/h 50N225掳C*** 306Coefficient of linear thermal expansion (CLTE), parallel15E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at 1.5mm nom. thickn.HBclassIEC 60695-11-10Thickness tested1.6mmIEC 60695-11-10Burning Behav. at thickness hHBclassIEC 60695-11-10Thickness tested0.82mmIEC 60695-11-10UL recognitionyesUL 94Oxygen index20%*** 4589-1/-2Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.4IEC 62631-2-1Relative permittivity, 1MHz4.1IEC 62631-2-1Dissipation factor, 100Hz16E-4IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity>1E13Ohm.mIEC 62631-3-1Surface resistivity>1E15OhmIEC 62631-3-2Electric strength35kV/mmIEC 60243-1Physical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.15%Sim. to *** 62Water absorption, 2mm0.35%Sim. to *** 62Density1710kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.04%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 4 to 6 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 260-270 掳C
Mold Temperature *) 75-85 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided. For grades containing flame retardants, a maximum temperature of 265 掳C should not be exceeded.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
Pre-Drying
CELANEX should always be dried before processing. Because of the necessary low maximum residual moisture content, the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationVW GroupNATURAL, no spec, special part approvalDiagrams
Copyright 漏 2025 All rights reserved.
CELANEX庐 2300 GV1/50
CELANEX庐 PBTPBT-GF50CharacteristicsRegional availabilityProcessingInjection MouldingDelivery formPelletsAdditivesRelease agentSpecial characteristicsHeat stabilised or stable to heatProduct TextChemical abbreviation according to *** 1043: PBT GF50. Moulding compound *** 7792-1 PBT, MGAR, 08-160, GF50. Polybutylene terephthalate, 50 % glass fiber reinforced. Flammability UL 94 HB minimum thickness 0.82 mm. Recognition by Underwriters Laboratories, USA (UL)Product information
ValueTest NormResin IdentificationPBT-GF50*** 1043Part Marking Code>PBT-GF50<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate5cm鲁/10min*** 1133Temperature250掳CLoad2.16kgMoulding shrinkage range, parallel0.3 - 0.4%*** 294-4, 2577Moulding shrinkage range, normal0.7 - 0.9%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus17000MPa*** 527-1/-2Tensile stress at break, 5mm/min165MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural strength240MPa*** 178Tensile creep modulus, 1h12500MPa*** 899-1Tensile creep modulus, 1000h9500MPa*** 899-1Charpy impact strength, 23掳C70kJ/m虏*** 179/1eUCharpy impact strength, -30掳C65kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C11.5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C11.5kJ/m虏*** 179/1eABall indentation hardness, H 961/30235MPa*** 2039-1Poisson&锛�39;s ratio0.33[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa215掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa228掳C*** 75-1/-2Temperature of deflection under load, 8 MPa185掳C*** 75-1/-2Vicat softening temperature, 50掳C/h 50N225掳C*** 306Coefficient of linear thermal expansion (CLTE), parallel15E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at 1.5mm nom. thickn.HBclassIEC 60695-11-10Thickness tested1.6mmIEC 60695-11-10Burning Behav. at thickness hHBclassIEC 60695-11-10Thickness tested0.82mmIEC 60695-11-10UL recognitionyesUL 94Oxygen index20%*** 4589-1/-2Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.4IEC 62631-2-1Relative permittivity, 1MHz4.1IEC 62631-2-1Dissipation factor, 100Hz16E-4IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity>1E13Ohm.mIEC 62631-3-1Surface resistivity>1E15OhmIEC 62631-3-2Electric strength35kV/mmIEC 60243-1Physical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.15%Sim. to *** 62Water absorption, 2mm0.35%Sim. to *** 62Density1710kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.04%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 4 to 6 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 260-270 掳C
Mold Temperature *) 75-85 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided. For grades containing flame retardants, a maximum temperature of 265 掳C should not be exceeded.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
Pre-Drying
CELANEX should always be dried before processing. Because of the necessary low maximum residual moisture content, the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationVW GroupNATURAL, no spec, special part approvalDiagrams
Copyright 漏 2025 All rights reserved.
CELANEX 2300 GV1/50
CELANEX庐 PBTPBT-GF50CharacteristicsRegional availabilityProcessingInjection MouldingDelivery formPelletsAdditivesRelease agentSpecial characteristicsHeat stabilised or stable to heatProduct TextChemical abbreviation according to *** 1043: PBT GF50. Moulding compound *** 7792-1 PBT, MGAR, 08-160, GF50. Polybutylene terephthalate, 50 % glass fiber reinforced. Flammability UL 94 HB minimum thickness 0.82 mm. Recognition by Underwriters Laboratories, USA (UL)Product information
ValueTest NormResin IdentificationPBT-GF50*** 1043Part Marking Code>PBT-GF50<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate5cm鲁/10min*** 1133Temperature250掳CLoad2.16kgMoulding shrinkage range, parallel0.3 - 0.4%*** 294-4, 2577Moulding shrinkage range, normal0.7 - 0.9%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus17000MPa*** 527-1/-2Tensile stress at break, 5mm/min165MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural strength240MPa*** 178Tensile creep modulus, 1h12500MPa*** 899-1Tensile creep modulus, 1000h9500MPa*** 899-1Charpy impact strength, 23掳C70kJ/m虏*** 179/1eUCharpy impact strength, -30掳C65kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C11.5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C11.5kJ/m虏*** 179/1eABall indentation hardness, H 961/30235MPa*** 2039-1Poisson&锛�39;s ratio0.33[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa215掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa228掳C*** 75-1/-2Temperature of deflection under load, 8 MPa185掳C*** 75-1/-2Vicat softening temperature, 50掳C/h 50N225掳C*** 306Coefficient of linear thermal expansion (CLTE), parallel15E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at 1.5mm nom. thickn.HBclassIEC 60695-11-10Thickness tested1.6mmIEC 60695-11-10Burning Behav. at thickness hHBclassIEC 60695-11-10Thickness tested0.82mmIEC 60695-11-10UL recognitionyesUL 94Oxygen index20%*** 4589-1/-2Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.4IEC 62631-2-1Relative permittivity, 1MHz4.1IEC 62631-2-1Dissipation factor, 100Hz16E-4IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity>1E13Ohm.mIEC 62631-3-1Surface resistivity>1E15OhmIEC 62631-3-2Electric strength35kV/mmIEC 60243-1Physical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.15%Sim. to *** 62Water absorption, 2mm0.35%Sim. to *** 62Density1710kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.04%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 4 to 6 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 260-270 掳C
Mold Temperature *) 75-85 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided. For grades containing flame retardants, a maximum temperature of 265 掳C should not be exceeded.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
Pre-Drying
CELANEX should always be dried before processing. Because of the necessary low maximum residual moisture content, the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationVW GroupNATURAL, no spec, special part approvalDiagrams
Copyright 漏 2025 All rights reserved.Properties
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Product Text
Properties
Diagrams
Disclaimer
Privacy Policy
Sitemap
Product Text
Properties
Diagrams
Disclaimer
Privacy Policy
Sitemap
Product Text
Properties
Diagrams
Disclaimer
Privacy Policy
Sitemap
Product Text
Properties
Diagrams
Disclaimer
Privacy Policy
Sitemap
Product Text
Properties
Diagrams
Disclaimer
Privacy Policy
Sitemap
Product Text
Properties
Diagrams
Disclaimer
Privacy Policy
Sitemap
Diagrams
CELANEX 2300 GV1/50
CELANEX庐 PBTPBT-GF50CharacteristicsRegional availabilityNorth America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Product information
ValueTest NormResin IdentificationPBT-GF50*** 1043Part Marking Code>PBT-GF50<*** 11469Rheological properties
ValueUnitTest NormMelt volume-flow rate5cm鲁/10min*** 1133Temperature250掳CLoad2.16kgMoulding shrinkage range, parallel0.3 - 0.4%*** 294-4, 2577Moulding shrinkage range, normal0.7 - 0.9%*** 294-4, 2577Mechanical properties
ValueUnitTest NormTensile modulus17000MPa*** 527-1/-2Tensile stress at break, 5mm/min165MPa*** 527-1/-2Tensile strain at break, 5mm/min1.6%*** 527-1/-2Flexural strength240MPa*** 178Tensile creep modulus, 1h12500MPa*** 899-1Tensile creep modulus, 1000h9500MPa*** 899-1Charpy impact strength, 23掳C70kJ/m虏*** 179/1eUCharpy impact strength, -30掳C65kJ/m虏*** 179/1eUCharpy notched impact strength, 23掳C11.5kJ/m虏*** 179/1eACharpy notched impact strength, -30掳C11.5kJ/m虏*** 179/1eABall indentation hardness, H 961/30235MPa*** 2039-1Poisson&锛�39;s ratio0.33[C][C]: CalculatedThermal properties
ValueUnitTest NormMelting temperature, 10掳C/min225掳C*** 11357-1/-3Temperature of deflection under load, 1.8 MPa215掳C*** 75-1/-2Temperature of deflection under load, 0.45 MPa228掳C*** 75-1/-2Temperature of deflection under load, 8 MPa185掳C*** 75-1/-2Vicat softening temperature, 50掳C/h 50N225掳C*** 306Coefficient of linear thermal expansion (CLTE), parallel15E-6/K*** 11359-1/-2Flammability
ValueUnitTest NormBurning Behav. at 1.5mm nom. thickn.HBclassIEC 60695-11-10Thickness tested1.6mmIEC 60695-11-10Burning Behav. at thickness hHBclassIEC 60695-11-10Thickness tested0.82mmIEC 60695-11-10UL recognitionyesUL 94Oxygen index20%*** 4589-1/-2Electrical properties
ValueUnitTest NormRelative permittivity, 100Hz4.4IEC 62631-2-1Relative permittivity, 1MHz4.1IEC 62631-2-1Dissipation factor, 100Hz16E-4IEC 62631-2-1Dissipation factor, 1MHz190E-4IEC 62631-2-1Volume resistivity>1E13Ohm.mIEC 62631-3-1Surface resistivity>1E15OhmIEC 62631-3-2Electric strength35kV/mmIEC 60243-1Physical/Other properties
ValueUnitTest NormHumidity absorption, 2mm0.15%Sim. to *** 62Water absorption, 2mm0.35%Sim. to *** 62Density1710kg/m鲁*** 1183Injection
ValueUnitDrying RecommendedyesDrying Temperature120掳CDrying Time, Dehumidified Dryer4hProcessing Moisture Content鈮�0.04%Melt Temperature Optimum250掳CMin. melt temperature240掳CMax. melt temperature260掳CScrew tangential speed0.1 - 0.3m/sMold Temperature Optimum80掳CMin. mould temperature60掳CMax. mould temperature130掳CAdditional informationInjection moldingPreprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0,02%. The drying should be done in a dry-air dryer (dew point <-30掳C) with a temperature of 120 to 140 掳C and a drying time of 4 to 6 hours. In case of longer residence times in the dry-air dryer, the temperature should be reduced to 100掳C.
The time between drying and processing should be kept as short as possible. The processing machine feed hopper should be closed during the processing operation.
Processing
Melt Temperature 260-270 掳C
Mold Temperature *) 75-85 掳C
Maximum Barrel Residence Time **) 5-10 min
Injection Speed fast
Peripheral screw speed max.0,3 m/sec
Back Pressure 10-30 bar
Injection Pressure 600-1000 bar
Holding Pressure 400-800 bar
Nozzle Design open design preferred
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided. For grades containing flame retardants, a maximum temperature of 265 掳C should not be exceeded.
Celanese recommends only externally heated hot runner systems.
*) For moulded parts with especially high requirements to the surface quality or dimensional stability, a mold temperature of up to 110 掳C can be advantageous.
**) If the cylinder temperatures are higher than the recommended maximum temperatures, the max. residence time in the barrel has to be reduced.
Pre-Drying
CELANEX should always be dried before processing. Because of the necessary low maximum residual moisture content, the use of dry air dryers is recommended. The dew point should be =<- 30掳 C. The time between drying and processing should be as short as possible.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
Automotive
OEMAdditional InformationVW GroupNATURAL, no spec, special part approvalDiagrams
Copyright 漏 2025 All rights reserved.
