| 是否进口：否 | 厂家(产地)：ZG | 牌号： 2002SW1 |
| 销售方式：自产自销 |
CELANEX庐 2002SW1
CELANEX庐 PBT
(PBT+PTFE)
Characteristics
Regional availability
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Processing
Injection Moulding
Delivery form
Pellets
Additives
Low wear / Low friction
Product Text
Celanex 2002SW1 Natural is an unreinforced PTFE-modified PBT with improved friction, sliding, and wear properties.
Product information
Value
Test Norm
Resin Identification
PBT+PTFE
*** 1043
Part Marking Code
>PBT+PTFE<
*** 11469
Rheological properties
Value
Unit
Test Norm
Melt volume-flow rate
21
cm鲁/10min
*** 1133
Temperature
250
掳C
Load
2.16
kg
Moulding shrinkage range, parallel
1.7 - 2.1
%
*** 294-4, 2577
Moulding shrinkage, normal
1.9
%
*** 294-4, 2577
Moulding shrinkage range, normal
1.7 - 2.1
%
*** 294-4, 2577
Mechanical properties
Value
Unit
Test Norm
Tensile modulus
2600
MPa
*** 527-1/-2
Tensile stress at yield, 50mm/min
56
MPa
*** 527-1/-2
Tensile strain at yield, 50mm/min
7
%
*** 527-1/-2
Nominal strain at break
19
%
*** 527-1/-2
Charpy notched impact strength, 23掳C
3.3
kJ/m虏
*** 179/1eA
Poisson&锛�39;s ratio
0.38[C]
[C]: Calculated
Thermal properties
Value
Unit
Test Norm
Melting temperature, 10掳C/min
225
掳C
*** 11357-1/-3
Glass transition temperature, 10掳C/min
60
掳C
*** 11357-1/-3
Temperature of deflection under load, 1.8 MPa
55
掳C
*** 75-1/-2
Vicat softening temperature, 50掳C/h 50N
190
掳C
*** 306
Electrical properties
Value
Test Norm
Comparative tracking index
600
IEC 60112
Physical/Other properties
Value
Unit
Test Norm
Humidity absorption, 2mm
0.2
%
Sim. to *** 62
Density
1340
kg/m鲁
*** 1183
Injection
Value
Unit
Drying Recommended
yes
Drying Temperature
120
掳C
Drying Time, Dehumidified Dryer
4
h
Processing Moisture Content
鈮�0.04
%
Melt Temperature Optimum
250
掳C
Min. melt temperature
240
掳C
Max. melt temperature
260
掳C
Screw tangential speed
0.1 - 0.3
m/s
Mold Temperature Optimum
80
掳C
Min. mould temperature
60
掳C
Max. mould temperature
130
掳C
Ejection temperature
190
掳C
Additional information
Injection molding
Preprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-500(240-260) deg F (deg C)
Nozzle Temperature 480-500(250-260) deg F (deg C)
Melt Temperature 460-500(235-260) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Processing Notes
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
CELANEX庐 2002SW1
CELANEX庐 PBT
(PBT+PTFE)
Characteristics
Regional availability
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Processing
Injection Moulding
Delivery form
Pellets
Additives
Low wear / Low friction
Product Text
Celanex 2002SW1 Natural is an unreinforced PTFE-modified PBT with improved friction, sliding, and wear properties.
Product information
Value
Test Norm
Resin Identification
PBT+PTFE
*** 1043
Part Marking Code
>PBT+PTFE<
*** 11469
Rheological properties
Value
Unit
Test Norm
Melt volume-flow rate
21
cm鲁/10min
*** 1133
Temperature
250
掳C
Load
2.16
kg
Moulding shrinkage range, parallel
1.7 - 2.1
%
*** 294-4, 2577
Moulding shrinkage, normal
1.9
%
*** 294-4, 2577
Moulding shrinkage range, normal
1.7 - 2.1
%
*** 294-4, 2577
Mechanical properties
Value
Unit
Test Norm
Tensile modulus
2600
MPa
*** 527-1/-2
Tensile stress at yield, 50mm/min
56
MPa
*** 527-1/-2
Tensile strain at yield, 50mm/min
7
%
*** 527-1/-2
Nominal strain at break
19
%
*** 527-1/-2
Charpy notched impact strength, 23掳C
3.3
kJ/m虏
*** 179/1eA
Poisson&锛�39;s ratio
0.38[C]
[C]: Calculated
Thermal properties
Value
Unit
Test Norm
Melting temperature, 10掳C/min
225
掳C
*** 11357-1/-3
Glass transition temperature, 10掳C/min
60
掳C
*** 11357-1/-3
Temperature of deflection under load, 1.8 MPa
55
掳C
*** 75-1/-2
Vicat softening temperature, 50掳C/h 50N
190
掳C
*** 306
Electrical properties
Value
Test Norm
Comparative tracking index
600
IEC 60112
Physical/Other properties
Value
Unit
Test Norm
Humidity absorption, 2mm
0.2
%
Sim. to *** 62
Density
1340
kg/m鲁
*** 1183
Injection
Value
Unit
Drying Recommended
yes
Drying Temperature
120
掳C
Drying Time, Dehumidified Dryer
4
h
Processing Moisture Content
鈮�0.04
%
Melt Temperature Optimum
250
掳C
Min. melt temperature
240
掳C
Max. melt temperature
260
掳C
Screw tangential speed
0.1 - 0.3
m/s
Mold Temperature Optimum
80
掳C
Min. mould temperature
60
掳C
Max. mould temperature
130
掳C
Ejection temperature
190
掳C
Additional information
Injection molding
Preprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-500(240-260) deg F (deg C)
Nozzle Temperature 480-500(250-260) deg F (deg C)
Melt Temperature 460-500(235-260) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Processing Notes
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.CELANEX庐 2002SW1
CELANEX庐 PBT
(PBT+PTFE)
Characteristics
Regional availability
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Processing
Injection Moulding
Delivery form
Pellets
Additives
Low wear / Low friction
Product Text
Celanex 2002SW1 Natural is an unreinforced PTFE-modified PBT with improved friction, sliding, and wear properties.
Product information
Value
Test Norm
Resin Identification
PBT+PTFE
*** 1043
Part Marking Code
>PBT+PTFE<
*** 11469
Rheological properties
Value
Unit
Test Norm
Melt volume-flow rate
21
cm鲁/10min
*** 1133
Temperature
250
掳C
Load
2.16
kg
Moulding shrinkage range, parallel
1.7 - 2.1
%
*** 294-4, 2577
Moulding shrinkage, normal
1.9
%
*** 294-4, 2577
Moulding shrinkage range, normal
1.7 - 2.1
%
*** 294-4, 2577
Mechanical properties
Value
Unit
Test Norm
Tensile modulus
2600
MPa
*** 527-1/-2
Tensile stress at yield, 50mm/min
56
MPa
*** 527-1/-2
Tensile strain at yield, 50mm/min
7
%
*** 527-1/-2
Nominal strain at break
19
%
*** 527-1/-2
Charpy notched impact strength, 23掳C
3.3
kJ/m虏
*** 179/1eA
Poisson&锛�39;s ratio
0.38[C]
[C]: Calculated
Thermal properties
Value
Unit
Test Norm
Melting temperature, 10掳C/min
225
掳C
*** 11357-1/-3
Glass transition temperature, 10掳C/min
60
掳C
*** 11357-1/-3
Temperature of deflection under load, 1.8 MPa
55
掳C
*** 75-1/-2
Vicat softening temperature, 50掳C/h 50N
190
掳C
*** 306
Electrical properties
Value
Test Norm
Comparative tracking index
600
IEC 60112
Physical/Other properties
Value
Unit
Test Norm
Humidity absorption, 2mm
0.2
%
Sim. to *** 62
Density
1340
kg/m鲁
*** 1183
Injection
Value
Unit
Drying Recommended
yes
Drying Temperature
120
掳C
Drying Time, Dehumidified Dryer
4
h
Processing Moisture Content
鈮�0.04
%
Melt Temperature Optimum
250
掳C
Min. melt temperature
240
掳C
Max. melt temperature
260
掳C
Screw tangential speed
0.1 - 0.3
m/s
Mold Temperature Optimum
80
掳C
Min. mould temperature
60
掳C
Max. mould temperature
130
掳C
Ejection temperature
190
掳C
Additional information
Injection molding
Preprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-500(240-260) deg F (deg C)
Nozzle Temperature 480-500(250-260) deg F (deg C)
Melt Temperature 460-500(235-260) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Processing Notes
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.CELANEX庐 2002SW1
CELANEX庐 PBT
(PBT+PTFE)
Characteristics
Regional availability
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Processing
Injection Moulding
Delivery form
Pellets
Additives
Low wear / Low friction
Product Text
Celanex 2002SW1 Natural is an unreinforced PTFE-modified PBT with improved friction, sliding, and wear properties.
Product information
Value
Test Norm
Resin Identification
PBT+PTFE
*** 1043
Part Marking Code
>PBT+PTFE<
*** 11469
Rheological properties
Value
Unit
Test Norm
Melt volume-flow rate
21
cm鲁/10min
*** 1133
Temperature
250
掳C
Load
2.16
kg
Moulding shrinkage range, parallel
1.7 - 2.1
%
*** 294-4, 2577
Moulding shrinkage, normal
1.9
%
*** 294-4, 2577
Moulding shrinkage range, normal
1.7 - 2.1
%
*** 294-4, 2577
Mechanical properties
Value
Unit
Test Norm
Tensile modulus
2600
MPa
*** 527-1/-2
Tensile stress at yield, 50mm/min
56
MPa
*** 527-1/-2
Tensile strain at yield, 50mm/min
7
%
*** 527-1/-2
Nominal strain at break
19
%
*** 527-1/-2
Charpy notched impact strength, 23掳C
3.3
kJ/m虏
*** 179/1eA
Poisson&锛�39;s ratio
0.38[C]
[C]: Calculated
Thermal properties
Value
Unit
Test Norm
Melting temperature, 10掳C/min
225
掳C
*** 11357-1/-3
Glass transition temperature, 10掳C/min
60
掳C
*** 11357-1/-3
Temperature of deflection under load, 1.8 MPa
55
掳C
*** 75-1/-2
Vicat softening temperature, 50掳C/h 50N
190
掳C
*** 306
Electrical properties
Value
Test Norm
Comparative tracking index
600
IEC 60112
Physical/Other properties
Value
Unit
Test Norm
Humidity absorption, 2mm
0.2
%
Sim. to *** 62
Density
1340
kg/m鲁
*** 1183
Injection
Value
Unit
Drying Recommended
yes
Drying Temperature
120
掳C
Drying Time, Dehumidified Dryer
4
h
Processing Moisture Content
鈮�0.04
%
Melt Temperature Optimum
250
掳C
Min. melt temperature
240
掳C
Max. melt temperature
260
掳C
Screw tangential speed
0.1 - 0.3
m/s
Mold Temperature Optimum
80
掳C
Min. mould temperature
60
掳C
Max. mould temperature
130
掳C
Ejection temperature
190
掳C
Additional information
Injection molding
Preprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-500(240-260) deg F (deg C)
Nozzle Temperature 480-500(250-260) deg F (deg C)
Melt Temperature 460-500(235-260) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Processing Notes
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.CELANEX庐 2002SW1
CELANEX庐 PBT
(PBT+PTFE)
Characteristics
Regional availability
North America
Europe
Asia Pacific
South and Central America
Near East/Africa
Global
Processing
Injection Moulding
Delivery form
Pellets
Additives
Low wear / Low friction
Product Text
Celanex 2002SW1 Natural is an unreinforced PTFE-modified PBT with improved friction, sliding, and wear properties.
Product information
Value
Test Norm
Resin Identification
PBT+PTFE
*** 1043
Part Marking Code
>PBT+PTFE<
*** 11469
Rheological properties
Value
Unit
Test Norm
Melt volume-flow rate
21
cm鲁/10min
*** 1133
Temperature
250
掳C
Load
2.16
kg
Moulding shrinkage range, parallel
1.7 - 2.1
%
*** 294-4, 2577
Moulding shrinkage, normal
1.9
%
*** 294-4, 2577
Moulding shrinkage range, normal
1.7 - 2.1
%
*** 294-4, 2577
Mechanical properties
Value
Unit
Test Norm
Tensile modulus
2600
MPa
*** 527-1/-2
Tensile stress at yield, 50mm/min
56
MPa
*** 527-1/-2
Tensile strain at yield, 50mm/min
7
%
*** 527-1/-2
Nominal strain at break
19
%
*** 527-1/-2
Charpy notched impact strength, 23掳C
3.3
kJ/m虏
*** 179/1eA
Poisson&锛�39;s ratio
0.38[C]
[C]: Calculated
Thermal properties
Value
Unit
Test Norm
Melting temperature, 10掳C/min
225
掳C
*** 11357-1/-3
Glass transition temperature, 10掳C/min
60
掳C
*** 11357-1/-3
Temperature of deflection under load, 1.8 MPa
55
掳C
*** 75-1/-2
Vicat softening temperature, 50掳C/h 50N
190
掳C
*** 306
Electrical properties
Value
Test Norm
Comparative tracking index
600
IEC 60112
Physical/Other properties
Value
Unit
Test Norm
Humidity absorption, 2mm
0.2
%
Sim. to *** 62
Density
1340
kg/m鲁
*** 1183
Injection
Value
Unit
Drying Recommended
yes
Drying Temperature
120
掳C
Drying Time, Dehumidified Dryer
4
h
Processing Moisture Content
鈮�0.04
%
Melt Temperature Optimum
250
掳C
Min. melt temperature
240
掳C
Max. melt temperature
260
掳C
Screw tangential speed
0.1 - 0.3
m/s
Mold Temperature Optimum
80
掳C
Min. mould temperature
60
掳C
Max. mould temperature
130
掳C
Ejection temperature
190
掳C
Additional information
Injection molding
Preprocessing
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Processing
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-500(240-260) deg F (deg C)
Nozzle Temperature 480-500(250-260) deg F (deg C)
Melt Temperature 460-500(235-260) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Processing Notes
Pre-Drying
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-40掳F (-40掳C) at 250掳F (120掳C) for minimum 4 hours.
Storage
For subsequent storage of the material in the dryer until processed (<= 60 h) it is necessary to lower the temperature to 100掳 C.
